[BraLUG] Problem - Handy T68i als Modem

[fatari at gmx.net]

Hallo,
ich habe hier ein Problem, bei dem ich nicht weiterkomme:
Ich wollte mein altes Handy als Modem nutzen, was ja prinzipiell möglich sein sollte, nur bekomme ich, wenn ich das richtig sehe, keine IP zugewiesen. Da ich noch Linux-Neuling bin, wäre ich für Hilfe dankbar!

Gruß Micha


Hier die relevanten Datei-Inhalte:
#    @/etc/chatscripts/
###
#
#    ispauth PAP - Zeit bis zum Abbruch?
TIMEOUT         120
#    abortstring - Abbruch wenn
ECHO ON
ABORT BUSY
ABORT 'NO CARRIER'
ABORT VOICE
ABORT 'NO DIALTONE'
ABORT 'NO DIAL TONE'
ABORT 'NO ANSWER'
ABORT DELAYED
ABORT 'ERROR'
#    modeminit
''              'ATE1'
#    AT+CGDCONT=<Profile Number>,"<PDP Type>","<APN>"
#    (I usually only use profile number 1, which i overwrite
#    with the settings i need. The PDP Type is usually IP)
OK              AT+CGDCONT=1,"IP","surfo2"
#    ispnumber - Einwahlnummer
#    For GPRS you need to dial a special number: ATDT*99***<profile number>#
#    The profile number should be the same as used in the AT+CGDCONT command
OK                     ATD*99#
#    ispconnect
CONNECT         \d\c



#    @/etc/ppp/peers/
###
#
# you usually need this if there is no PAP authentication
noauth
# the chat script (be sure to edit that file, too!)
connect "/usr/sbin/chat -v -f /etc/chatscripts/gprsT68i_cs"
# set up routing to go through this PPP link
defaultroute
# the device for connecting /dev/ircomm0 or similar
/dev/rfcomm0
# speed for GPRS 115200 for UMTS 460800
115200
# reconnect on disconnect
persist
# be extra verbose
debug
# you may need these
passive
noipdefault
noproxyarp
ipcp-accept-local
ipcp-accept-remote
ipcp-restart 2
ipcp-max-configure 20
ipcp-max-failure 20
asyncmap 0xa0000
novj
nodeflate
nobsdcomp
# use remote DNS
usepeerdns
# with GPRS, authentication is normally done  automatically
# via your cellphone number, so leave login name empty
user ""



Die Fehlermeldung:

t30linux:/# pon gprsT68i
AT
OK
ATE0
OK

OK

OK

OK

CONNECT
Serial connection established.
using channel 1
Using interface ppp0
Connect: ppp0 <--> /dev/rfcomm0
sent [LCP ConfReq id=0x1 <asyncmap 0xa0000> <magic 0x54bc2cab> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
sent [LCP ConfAck id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfRej id=0x1 <magic 0x54bc2cab>]
sent [LCP ConfReq id=0x2 <asyncmap 0xa0000> <pcomp> <accomp>]
rcvd [LCP ConfAck id=0x2 <asyncmap 0xa0000> <pcomp> <accomp>]
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x1]
sent [IPCP ConfNak id=0x1 <addr 0.0.0.0>]
rcvd [IPCP ConfRej id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
sent [IPCP ConfReq id=0x2 <addrs 0.0.0.0 0.0.0.0>]
rcvd [IPCP ConfReq id=0x2 <addr 0.0.0.0>]
sent [IPCP ConfRej id=0x2 <addr 0.0.0.0>]
rcvd [IPCP ConfRej id=0x2 <addrs 0.0.0.0 0.0.0.0>]
sent [IPCP ConfReq id=0x3]
rcvd [IPCP ConfReq id=0x3]
sent [IPCP ConfAck id=0x3]
rcvd [IPCP ConfAck id=0x3]
Could not determine local IP address
Connect time 0.2 minutes.
Sent 64 bytes, received 58 bytes.
sent [IPCP TermReq id=0x4 "Could not determine local IP address"]
Modem hangup
Connection terminated.


-- 
Psssst! Schon vom neuen GMX MultiMessenger gehört?
Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger